For years I have been using a Netgear WNDR4500 running DD-wrt v24-sp2 as a wireless bridge to the second side of my house that feeds a switch with about 10 devices (TVs, desktop computers, etc). This all works pretty good (I occasionally need to unplug/plug the switch because of connection issues but its not a huge deal.)
About DD-WRT is a Linux based alternative OpenSource firmware suitable for a great variety of WLAN routers and embedded systems. The main emphasis lies on providing the easiest possible handling while at the same time supporting a great number of functionalities within the framework of the respective hardware platform used. Posted: Fri Dec 28, 2007 23:30 Post subject: : I have the RC6-8727 working fine for Repeater Bridge mode. Set up the Repeater on the SAME subnet. 192.168.1.2 is fine if you host is 192.168.1.1 I have followed the REPEATER BRIDGE wiki (https://www.dd-wrt.com/wiki/index.php/Repeater_Bridge) closely with the base station / WAP and the remote WAP configured in accordance with its directions. Internet access through the base station / WAP via 2.4Ghz WiFi works flawlessly but access through the 2.4Ghz WiFi remote WAP does not work at all. Вопросы и обсуждения, связанные с устройствами Ubiquiti Litestation, Nanostation и Powerstation и работой DD-WRT на этих устройствах. Moderators kodo , SaintReset , vasek00 , jwh7 , egc , js1662 , msoengineer , kernel-panic69
If you find the OpenWrt device itself is only accessible from those computers directly connected to the W-LAN AP, not from the ones connected to the OpenWrt W-LAN client, when in the 192.168.1.0 subnet, Make sure the Local IPv4 address setting in the Relay bridge interface matches the ip address of the wireless uplink.
You must use wpa2-aes for things to work reliably. The only other that works reliably is wep. You might have to change your primary router to a security that works with dd-wrt. Hit SAVE, (or APPLY if you wish to) Go to the wireless, basic settings page and change the wireless mode to Client Bridge.
Oct 19, 2011 · Many consumers and network administrators turn to DD-WRT when seeking for the optimal choice in setting up a Client Bridge. Once they go DD-WRT, they never seem to go back due to the simplicity, customization possibilities, and the ease of the setup process. There are a few basic networking terms to become acquainted with before reading further. Jul 07, 2017 · DD-WRT Repeater Bridge WIFI Extender With Netgear WNR2000v3 & TP Link WDR4300 - Duration: 34:20. Richard Lloyd 96,932 views. 34:20. 5 Things I Do to Have a Better Home Network - Duration: 10:08. If you find the OpenWrt device itself is only accessible from those computers directly connected to the W-LAN AP, not from the ones connected to the OpenWrt W-LAN client, when in the 192.168.1.0 subnet, Make sure the Local IPv4 address setting in the Relay bridge interface matches the ip address of the wireless uplink. The funny poles are actually DD-WRT routers and one is configured as the primary. If your modem has wireless and a switch you can just leave that primary router out, since it is just configured as a standard access point. The secondary is actually a DD-WRT router in repeater bridge mode. Feb 04, 2019 · DD-WRT is a complete toolkit. It comes with nearly everything you could want in a router as well as a whole lot more that you’ll probably never even look at. That’s simultaneously one of DD-WRT’s biggest strengths and weaknesses. For people looking for maximum control, DD-WRT’s plethora of options is a welcome breath of fresh air. Firstly, under step 6 of the dd-wrt Repeater_Bridge guide, DO NOT create a Virtual Interface. I found that when the repeater router (the d-link D4) was broadcasting its own network name (or SSID) independently of the primary router (the d-link D5) through a virtual interface it caused conflict with the primary router's wifi signal and